Cox Engines Forum
You are not logged in! Please login or register! Guests are limited to posting in the "General Questions (Guest Posting Allowed)" section only. Becoming a member is fast, easy and FREE!


Log in

I forgot my password

Search
 
 

Display results as :
 


Rechercher Advanced Search

Cox Engine of The Month
November-2017
MauricioB's

"Cox Tee Dee .010"



PAST WINNERS
Speed Contest 2018
CEF Traveling Engine

Gallery


Win This Engine!
The Traveling Prop
World of Aviation

Replacing a Wen Mac spraybar and needle with a Cox

View previous topic View next topic Go down

Help! Replacing a Wen Mac spraybar and needle with a Cox

Post  akjgardner on Sun Apr 02, 2017 7:52 pm

I Remember reading on here sometime back someone was replacing a wenmac spraybar and needle with a Cox one, but I can't find it , Can some one Help? Thanks
avatar
akjgardner
Platinum Member
Platinum Member

Posts : 750
Join date : 2014-12-28
Age : 58
Location : Milan Indiana

View user profile

Back to top Go down

Help! Re: Replacing a Wen Mac spraybar and needle with a Cox

Post  dckrsn on Sun Apr 02, 2017 8:19 pm

I don't know about a Wen Mac conversion, but I've done the OK Cub/Cox conversion.
In either case, you'll have to drill out the case for the larger spraybar fit,or sleeve the
case for a smaller one. The OK job was close, and only required a little JB weld to seal
the deal. The Cox postage stamp(128 tpi) assembly is the one you want to use.
Bob

avatar
dckrsn
Diamond Member
Diamond Member

Posts : 1806
Join date : 2010-10-21
Age : 64
Location : Long Island, NY USA Earth

View user profile

Back to top Go down

Help! Re: Replacing a Wen Mac spraybar and needle with a Cox

Post  akjgardner on Sun Apr 02, 2017 8:22 pm

[quote="dckrsn"]I don't know about a Wen Mac conversion, but I've done the OK Cub/Cox conversion.
In either case, you'll have to drill out the case for the larger spraybar fit,or sleeve the
case for a smaller one. The OK job was close, and only required a little JB weld to seal
the deal. The Cox postage stamp(128 tpi) assembly is the one you want to use.
Bob

Thanks Bob
avatar
akjgardner
Platinum Member
Platinum Member

Posts : 750
Join date : 2014-12-28
Age : 58
Location : Milan Indiana

View user profile

Back to top Go down

Help! Re: Replacing a Wen Mac spraybar and needle with a Cox

Post  batjac on Sun Apr 02, 2017 10:32 pm

Here's a link to the thread I did on using a Cox spraybar in a Wen-Mac engine:

https://www.coxengineforum.com/t8206-follow-the-bouncing-brain

The Mixer Mark
avatar
batjac
Diamond Member
Diamond Member

Posts : 1447
Join date : 2013-05-22
Age : 54
Location : Portland, OR, USA

View user profile

Back to top Go down

Help! Re: Replacing a Wen Mac spraybar and needle with a Cox

Post  akjgardner on Mon Apr 03, 2017 5:27 am

Thanks Mark, I Knew I had seen someone on here replacing a Wen Mac spray bar with a Cox ,but didn't Who, Thanks again
avatar
akjgardner
Platinum Member
Platinum Member

Posts : 750
Join date : 2014-12-28
Age : 58
Location : Milan Indiana

View user profile

Back to top Go down

Help! Re: Replacing a Wen Mac spraybar and needle with a Cox

Post  Sponsored content


Sponsored content


Back to top Go down

View previous topic View next topic Back to top

- Similar topics

 
Permissions in this forum:
You cannot reply to topics in this forum