Log in
Search
Latest topics
» Blue backplate postage stamp engineby getback Today at 6:46 am
» Cox Ryan ST 2.0
by rsv1cox Today at 6:38 am
» COX Postage Stamp engine -Babe Bee & Horseshoe Backplate adapters
by GallopingGhostler Today at 6:33 am
» Jim Walkers FireBee - This is going to be fun
by rsv1cox Yesterday at 3:45 pm
» Hawk had breakfast and then took a bath
by GallopingGhostler Yesterday at 2:34 pm
» Prop Rod - resto to a runner
by rsv1cox Yesterday at 12:41 pm
» Jim Walker Firebaby
by rsv1cox Yesterday at 12:24 pm
» Internet buy
by Ken Cook Yesterday at 9:15 am
» Artwork for Otto Kuhni
by GallopingGhostler Yesterday at 8:26 am
» Sherline lathe wont run
by getback Yesterday at 7:15 am
» Roddie's water-cooling bottle for bench-running
by roddie Tue May 14, 2024 7:38 pm
» Feed Station Zebra.. Spring 2022
by roddie Tue May 14, 2024 5:59 pm
Happy Birthday 1/2A NUT!!!
Page 2 of 2
Page 2 of 2 • 1, 2
Re: Happy Birthday 1/2A NUT!!!
I love that type of spinner. I pick one up when I can for my Coxes, I'd like to replace all of them with studs and spinners. The 1/2A ones we get are either knockoffs or genuine Ron Valentine products.
I don't know if they make ones to fit a Norvel shaft. Probably so. I just use long bolts on them. 3mm I think.
Rusty
I don't know if they make ones to fit a Norvel shaft. Probably so. I just use long bolts on them. 3mm I think.
Rusty
_________________
Don't Panic!
...and never Ever think about how good you are at something...
while you're doing it!
My Hot Rock & Blues Playlist
...and never Ever think about how good you are at something...
while you're doing it!
My Hot Rock & Blues Playlist
RknRusty- Rest In Peace
- Posts : 10869
Join date : 2011-08-10
Age : 68
Location : South Carolina, USA
Re: Happy Birthday 1/2A NUT!!!
You can tap them out to 3mm for the .049 and .061 Norvels they are a bit heavy but do look great.
I particularly like them with the APC 6x4 (hub dia is 1/2A size) and the Norvel .074 requires a 4mm tap but weight is not an issue with the .074 that engine has no problem spinning the additional mass.
Did you check out the HP/Watt/Thrust/MPH calculator? its very good and the only one I will use now.
I keep a icon on my desk top now for fast reference.
I particularly like them with the APC 6x4 (hub dia is 1/2A size) and the Norvel .074 requires a 4mm tap but weight is not an issue with the .074 that engine has no problem spinning the additional mass.
Did you check out the HP/Watt/Thrust/MPH calculator? its very good and the only one I will use now.
I keep a icon on my desk top now for fast reference.
1/2A Nut- Top Poster
- Posts : 3441
Join date : 2013-10-20
Age : 60
Location : Brad in Texas
Page 2 of 2 • 1, 2
Similar topics
» Happy Birthday Bob!!!
» A Happy belated Birthday to balogh !
» Happy π Birthday
» happy birthday happy dad
» Happy Birthday Oldenginerod
» A Happy belated Birthday to balogh !
» Happy π Birthday
» happy birthday happy dad
» Happy Birthday Oldenginerod
Page 2 of 2
Permissions in this forum:
You cannot reply to topics in this forum