Log in
Search
Latest topics
» Stealth SB-Xby Admin Today at 8:28 pm
» ST .35 STUNT / VOODOO / ZERO POINT ZERO NITRO
by TD ABUSER Today at 7:45 pm
» SUPERTIGER .15 PROJECT
by TD ABUSER Today at 7:42 pm
» For sale -- Cox Custom Carburetors for Tee Dee engines
by sosam117 Today at 5:23 pm
» WHERE ARE YOU BUYING YOUR FUEL AND GLOW PLUGS...?
by TD ABUSER Today at 4:35 pm
» Waiting for Engines from Ken Enya
by sosam117 Today at 4:33 pm
» Unusual Cox 049 cylinder - Need help identifying
by anm2 Today at 4:12 pm
» Jim Walker Bonanza etc.
by rsv1cox Today at 2:57 pm
» What's the Best Reed for Cox Reed Valve Engines.
by roddie Today at 1:37 pm
» Fuel choice
by 1975 control line guy Yesterday at 4:01 pm
» "Fall S.M.A.L.L." Video 3.
by GallopingGhostler Yesterday at 2:37 pm
» Gifted Fox
by Ken Cook Yesterday at 11:12 am
Cox Engine of The Month
August-2024
balogh's
![](https://i.servimg.com/u/f95/15/46/86/41/1_balo14.jpg)
"Cox TD09 R/C Beast of Burden featuring Kamtechnik head and DIY metallic fuel nipple"
![](https://i.servimg.com/u/f95/15/46/86/41/sponso12.png)
PAST WINNERS
balogh's
![](https://i.servimg.com/u/f95/15/46/86/41/1_balo14.jpg)
"Cox TD09 R/C Beast of Burden featuring Kamtechnik head and DIY metallic fuel nipple"
![](https://i.servimg.com/u/f95/15/46/86/41/sponso12.png)
PAST WINNERS
Well, Now I've Done It.....
Page 2 of 2
Page 2 of 2 • 1, 2
Jason_WI- Top Poster
Posts : 3123
Join date : 2011-10-09
Age : 49
Location : Neenah, WI
Jason_WI- Top Poster
Posts : 3123
Join date : 2011-10-09
Age : 49
Location : Neenah, WI
Jason_WI- Top Poster
Posts : 3123
Join date : 2011-10-09
Age : 49
Location : Neenah, WI
Re: Well, Now I've Done It.....
Thats great news! I am not that upset about the holes being off as I now know I have some work to do on the file. But I am even more happy that the TD mount worked out the way it did, and more work went into it. Also thank you very much for taking the time to do the initial test of the pieces.
By looking at it, it looks like I should move the holes in a millimeter each. I will definately change that.
Thanks again!
By looking at it, it looks like I should move the holes in a millimeter each. I will definately change that.
Thanks again!
NEW222- Top Poster
- Posts : 3895
Join date : 2011-08-13
Age : 45
Location : oakbank, mb
Re: Well, Now I've Done It.....
Not bad Chancey , i am sure i could do no better.. Do you measure the hole from the center or the rim ? O Jason ar eyou still working on the zip starter for the GTP cars?
![Smile](https://2img.net/i/fa/i/smiles/icon_smile.gif)
getback- Top Poster
Posts : 10326
Join date : 2013-01-18
Age : 67
Location : julian , NC
Re: Well, Now I've Done It.....
Thanks Eric. I drew it up by tracing a horseshoe backplate to paper then drawing a grid on it to get the measurements. No science behind it, I went old school. Did my best to draw teh holes as accurate as possible with a thin lead mechanical pencil. I had to do that as my digital calipers were dead..... Need a new battery in them. But I have since redrawn the backplate with 4mm holes instead of 3mm, and also moved both in 1 mm I believe. Now only time will tell. Holes being a bit bigger is not a concern as it is just a spacer.
NEW222- Top Poster
- Posts : 3895
Join date : 2011-08-13
Age : 45
Location : oakbank, mb
Page 2 of 2 • 1, 2
Page 2 of 2
Permissions in this forum:
You cannot reply to topics in this forum