Log in
Search
Latest topics
» Simple Glidersby rdw777 Today at 6:25 pm
» Foam hand kids glider converted to 0.049 CL
by rdw777 Today at 6:11 pm
» Weird search for a single comic from an old Mad Magazine
by Kim Today at 1:44 pm
» Scientific "Zipper" Build...Zipper Flys!.
by getback Today at 7:27 am
» Cox .049 Tee Dee engines back in stock (limited availablility)
by GallopingGhostler Today at 1:05 am
» Very off-topic.........Time passes and not always for the best......
by rsv1cox Yesterday at 2:47 pm
» Golden Bee basic running problem
by 944_Jim Yesterday at 12:44 pm
» Roddie-Rigger.. a 2005 original design
by roddie Wed Jul 24, 2024 11:48 pm
» Jim Walker Bonanza etc.
by rsv1cox Wed Jul 24, 2024 6:30 pm
» Throttles for Cox Tee Dee .049 / .020 / .010 engines --- videos
by sosam117 Wed Jul 24, 2024 8:54 am
» Introducing our Cox .049 TD Engines
by Admin Tue Jul 23, 2024 2:00 am
» Project Cox .049 r/c & Citabrian Champion
by getback Mon Jul 22, 2024 4:14 pm
Cox Engine of The Month
July-2024
robot797's
![](https://i.servimg.com/u/f95/15/46/86/41/3_robo10.jpg)
"ULTIMITE COX 010: it has a clutch, E starter, throttle, exhaust, aluminum tank, aluminum venturi, gearbox with forward and reverse, and now its on a custom drawn and printed stand"
![](https://i.servimg.com/u/f95/15/46/86/41/sponso12.png)
PAST WINNERS
robot797's
![](https://i.servimg.com/u/f95/15/46/86/41/3_robo10.jpg)
"ULTIMITE COX 010: it has a clutch, E starter, throttle, exhaust, aluminum tank, aluminum venturi, gearbox with forward and reverse, and now its on a custom drawn and printed stand"
![](https://i.servimg.com/u/f95/15/46/86/41/sponso12.png)
PAST WINNERS
PAW 100 Spraybar Orientation
Page 1 of 1
PAW 100 Spraybar Orientation
Hi there again. As you may already know, I had just received PAW 100 diesel engine to try out and run for the season. But when I got it, it was gummed up, so I disassembled it to de-gum it. My main question now as I was assembling it is the orientation of the spraybar. There are 2 holes in it near the center of the venturi. They both appear in the venturi, and also both are at approximately equal offset from the center. Where is it advised these holes are located when I tighten down the spraybar? If it makes a difference, the fuel line nipple is to the right, and the needle is on the left, as viewed from inside the cockpit / behind the engine. Thank you.
NEW222- Top Poster
- Posts : 3895
Join date : 2011-08-13
Age : 45
Location : oakbank, mb
Re: PAW 100 Spraybar Orientation
The holes are set apart by less than 180°, and both holes should point downstream along the air-flow direction. I.e. when looking through the fully assembled and mounted venturi from the top, you should not see any of the holes.
Surfer_kris- Diamond Member
- Posts : 1909
Join date : 2010-11-20
Location : Sweden
Re: PAW 100 Spraybar Orientation
Ok. I just installed the spraybar and tightened it down. Holes are not visible from the venturi opening, and did my best at orienting them equally as best I could downwards. Thank you. Now to just get me some ether. Hopefully tomorrow. Thank you.
NEW222- Top Poster
- Posts : 3895
Join date : 2011-08-13
Age : 45
Location : oakbank, mb
![-](https://2img.net/i/empty.gif)
» Port orientation
» Needle Valve Orientation on Medallaion and Tee Dee
» black window questions
» Thanks again rsv1cox "Bob"
» Medallion Spraybar.
» Needle Valve Orientation on Medallaion and Tee Dee
» black window questions
» Thanks again rsv1cox "Bob"
» Medallion Spraybar.
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum