Log in
Search
Latest topics
» Fox .35 Modifications by GallopingGhostler Today at 10:14 pm
» Happy Anzac Day!
by 706jim Today at 6:44 pm
» Project Cox .049 r/c & Citabrian Champion
by MauricioB Today at 4:08 pm
» Jim Walkers FireBee - This is going to be fun
by rsv1cox Today at 3:56 pm
» Revivng Some Childhood Classics
by rsv1cox Today at 7:17 am
» Introducing our Cox .049 TD Engines
by getback Today at 6:20 am
» Roddie's flat-bottomed boat..
by Levent Suberk Today at 12:23 am
» Cox powered jet-pump for model Sprint Boat
by roddie Yesterday at 10:25 pm
» Micro Draco Gets to Fly on a Beautiful Morning.
by rdw777 Yesterday at 8:15 pm
» Jim Walker Firebaby
by rdw777 Yesterday at 8:06 pm
» Hydro-bat by Vic Smeed: engine probs
by GallopingGhostler Yesterday at 5:12 pm
» Roddie-Rigger.. a 2005 original design
by roddie Yesterday at 3:39 pm
Cox Engine of The Month
That screw.. the one you found on the floor..
Page 1 of 1
That screw.. the one you found on the floor..
It wasn't by divine intervention.. it came from somewhere. I found it a few weeks ago in my workshop, looked at it.. and thought; gee... I wonder where this came from? I put it in my catch-all tray on my workbench.. because it was a special screw... a peculiar headed Phillips machine screw... not at all like my other screws... must be for something important. Well.. I found out where it came from this morning, just as I was sitting down with a cup of coffee at my laptop.. to log into my beloved CEF forum.
My folding-chair collapsed... needless to say; that woke me up faster than the coffee. We are ok... me and the chair. I had to pull a bent support-rod out of my butt... and straighten it in the vise, find the "special" screw.. reinstall it.. refill my coffee, and I was back in commission!
We have several of these chairs... and this past holiday season, my Mother-in-law was sitting in one... Wouldn't it have been funny if..
My folding-chair collapsed... needless to say; that woke me up faster than the coffee. We are ok... me and the chair. I had to pull a bent support-rod out of my butt... and straighten it in the vise, find the "special" screw.. reinstall it.. refill my coffee, and I was back in commission!
We have several of these chairs... and this past holiday season, my Mother-in-law was sitting in one... Wouldn't it have been funny if..
Re: That screw.. the one you found on the floor..
Glad your ok also chair , mother-and-law yes that's a gasser had a couple of them and there fat asses / good , better than Gods advice ! just got through flying the stuntman 23 with the medallion on it that was a lot better than the bee have to refigure the tank again. right now back outside to get some limbs off my shop I have a hole didn't know I had Getback
getback- Top Poster
-
Posts : 10114
Join date : 2013-01-18
Age : 66
Location : julian , NC
Re: That screw.. the one you found on the floor..
getback wrote: Glad your ok also chair , mother-and-law yes that's a gasser had a couple of them and there fat asses / good , better than Gods advice ! just got through flying the stuntman 23 with the medallion on it that was a lot better than the bee have to refigure the tank again. right now back outside to get some limbs off my shop I have a hole didn't know I had Getback
Well Eric... if you find any "screws" on the ground... make sure they weren't holding the shop's roof up!!!
Re: That screw.. the one you found on the floor..
That's funny Roddie, glad you, your chair and your backside are ok.
Cribbs74- Moderator
-
Posts : 11895
Join date : 2011-10-24
Age : 50
Location : Tuttle, OK
Similar topics
» Getting them up off the floor, a losing battle
» My little bitty buddy slithering around my garage floor this morning.
» Server not found.. has Been Found?
» Before I screw up
» Fun with Generic, Non-Threatening Title
» My little bitty buddy slithering around my garage floor this morning.
» Server not found.. has Been Found?
» Before I screw up
» Fun with Generic, Non-Threatening Title
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum